Manual Every Control Cn101

View and Download Yamaha CS1D service manual online. CS1D Music Mixer pdf manual download. IMCs01Software Manual Ver. 1.0e 1 © 1998 – 2003, iXs Research Corporation All right reserved. IMCs01Software Manual.

Wiring the relay creates a half bridge. When 12V is applied to Pin 8, the relay will activate.

Wiring the relay as shown will cause the voltage across Pins 5 and 6 to change from -12V to +12V. The default position of the relay is when the relay is deactivated, the active position is when Pin 8 has 12V on it. The actuator can be wired in 2 ways. One way, the default position is extended, and the timer controls retraction. The other way, the default position is retracted, and the timer controls extension.

For this example we're using retracted as default and extended when the relay activates. To change the actuators position when the relay is deactivated, switch the wires on Pins 5 and 6.

Wire the relay as follows: - Connect Pin 1 to Pin 4 - Connect Pin 4 to +12V - Connect Pin 2 to Pin 3 - Connect Pin 3 to Pin 7 - Connect Pin 7 to GND - Connect the two wires of the actuator to Pins 5 and 6, so when the relay is deactivated, the actuator is retracted. If the relay extends, just flip the connections on 5 and 6. See the wiring diagram for details. The timer is used to control when the actuator is activated. The timer is programmed to choose which times the switch is closed. This switch is connected to the relay, choosing which times the relay is active and deactivated. By wiring the switch to 12V, the timers 'ON' times will correspond to the relay being activated.

If you wire the switch to GND, the timers 'ON' times will control when the switch is deactivated. For this example we're setting the timer's 'ON' times to correspond to the relay being activated.

First things first, you need to solder wires to the timer. It doesn't matter which direction you solder the wires, polarity doesn't matter for both the switch and the power connections. Once the timer has wires soldered to it, it can be added to the relay as follows: - Connect one side of power to +12V - Connect the other side of power to GND - Connect one side of the switch to +12V (or GND) - Connect the other side of the switch to Pin 8. Once everything is wired up, the actuator can be tested. Pressing the 'Manual' button on the timer will simulate the timer activating.

The orange light will turn on and the switch will close. This should cause the relay to activate and the actuator to extend. If not, check your wiring. The timer has the capability to hold 17 different timing programs. This gives a huge amount of flexibility, allowing you to program many different sequences to control your actuator.

Download to aru majutsu no index movie endymion no kiseki subtitle indonesia indonesia. Download Movie To Aru Majutsu no Index BD Sub Indo, Download Movie To Aru Index Endymion no Kiseki BD Sub Indo, Download Movie To Aru Index Sub Indo MKV 720P, MKV 480P, batch Download Movie Toaru Majutsu no Index: Endymion no Kiseki BD Subtitle Indonesia. Download Anime Toaru Majutsu no Index – Endymion no Kiseki Subtitle Indonesia Toaru Majutsu no Index Movie – Endymion no Kiseki Subtitle Indonesia.MKV.MP4.3GP Toaru Majutsu no Index Movie – Endymion no Kiseki Subtitle Indonesia.MP4.

First things first, you need to program the current day and time. The timer has a small internal battery so it can go without power for a short amount of time. To be safe, assume that if it loses power you'll have to reset all the settings. Check the annotations on the image to see which button is which: -To program the day, hold down the clock button, and press D+ until the correct day is shown. -To program the hour, hold down the clock button, and press H+ until the correct hour is shown (its a 24 hour clock) -To program the minute, hold down the clock button, and press M+ until the correct minutes are shown. -To program different timing schedules, press the P button. In the bottom left, you will see a small number (1-17) with a ON or OFF below it.

When you first go through the programs, they will be set to --:-. Pressing the P button again will cycle through 1 ON, 1 OFF, 2 ON, 2 OFF. The numbers represent the program number. When you are on the ON section of the program, you are programming the times that the switch will be closed and the relay active. When you are in the OFF section of the program, you are setting the times the switch will be open and the relay deactivated. When you are in the program menu that you want (for example, 1 ON) you can press the D+, H+, and M+ buttons to set the times. When pressing the D+ button, the days will cycle through 15 options.